Jotun Penguard Tie Coat 100

Two component polyamide cured epoxy tie coat/sealer on top of inorganic zinc silicate primers, galvanised steel and thermally sprayed zinc. A primer for a complete system in atmospheric environments.

• Pack Size: 19.5 litres

• Colour: Red

• Gloss Level: Semi-gloss

--

 

Jotun Penguard Tie Coat 100

Jotun Penguard Tie Coat 100 is a two component, polyamide cured, high molecular weight epoxy holding primer, sealer and tie coat for use in atmospheric environments.

• Pack Size: 19.5 litres

• Colour: Red

• Gloss Level: Semi-gloss

• Number of components: Two (13 litres + 6.5 litres)

 

Product Description

Jotun Penguard Tie Coat 100 is a two component, polyamide cured, high molecular weight epoxy coating. Specially designed as holding primer, sealer and as a tie coat on top of inorganic zinc silicate primers, galvanized steel and thermally sprayed zinc. To be used as primer in a complete system in atmospheric environments.

 

Recommended Uses

Suitable for structural steel and piping exposed to highly corrosive environments. Recommended for offshore environments, refineries, power plants, bridges, buildings and mining equipment.

 

Approvals and Certificates

Pre-qualification testing in accordance with NORSOK M-501, Rev. 5, System 1, suitable for exterior exposure in offshore environment, below 120 °C. When used as part of an approved scheme, this material has the following certification:

• Low Flame Spread in accordance with EU Directive for Marine Equipment. Approved in accordance with parts 5 and 2 of Annex 1 of IMO 2010 FTP Code, or Parts 5 and 2 of Annex 1 of IMO FTPC when in compliance with IMO 2010 FTP Code Ch. 8.

Additional certificates and approvals may be available on request.

 

Surface Preparation

To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any contamination. Optimum performance, including adhesion, corrosion protection, heat resistance and chemical resistance is achieved with recommended surface preparation as follows:

 

Galvanised Steel

• The surface should be clean, dry and appear with a rough and dull profile

• Sweep blast-cleaning is recommended using non-metallic abrasive, leaving a clean, rough and even pattern

 

Coated Surfaces

• Clean, dry and undamaged compatible coating

 

Application

• Air Spray / Airless Spray: Nozzle tip (inch/1000) 15-19; Pressure at nozzle (minimum) 150 bar/2100 psi

• Brush: Recommended for stripe coating and small areas. Care must be taken to achieve the specified dry film thickness

 

Product Mixing Ratio (By Volume)

• Component A: 2 parts

• Component B: 1 part

 

Thinner

Jotun Thinner No. 17

 

Technical Data

• Surface (touch) dry (at 23 °C): 1 hour

• Walk-on-dry (at 23 °C): 6.5 hours

• Dry to over coat (minimum) (at 23 °C): 6 hours

• Dried/cured for service (at 23 °C): 7 days

• Induction time: 30 mins

• Pot life: 4 hours

• Heat resistant - dry, atmospheric: Continuous 120°C; peak 140°C. Peak temperature duration max. 1 hour

For maximum overcoating intervals, refer to the Application Guide for this product.

Note:

• Drying and curing times are determined under controlled temperatures and relative humidity below 85 %, and at average of the DFT range for the product

• Dry to over coat, minimum: The recommended shortest time before the next coat can be applied

• Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal tackiness

• Dried/cured for service: Minimum time before the coating can be permanently exposed to the intended environment/medium

• The temperatures listed relate to retention of protective properties. Aesthetic properties may suffer at these temperatures

Please refer to the technical data sheet for further technical data or contact us for advice.

 

Product Compatibility

Depending on the actual exposure of the coating system, various primers and topcoats can be used in combination with this product. Some examples are shown below. Contact us for specific system recommendation.

• Previous coat: zinc silicate, epoxy

• Subsequent coat: acrylic, epoxy, polyurethane

 

Packaging

• Component A: volume 13 litres; container size 20 litres

• Component B: volume 6.5 litres; container size 10 litres

 

Storage

• The product must be stored in accordance with national regulations

• Keep the containers in a dry, cool, well ventilated space and away from sources of heat and ignition

• Containers must be kept tightly closed

• Handle with care

 

Shelf life at 23 °C

• Component A: 24 months

• Component B: 48 months

Note: In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf life, thereafter the paint quality is subject to re-inspection.

 

Health and Safety

• This product is for professional use only

• The applicators and operators shall be trained, experienced and have the capability and equipment to mix/stir and apply the coatings correctly and according to the technical documentation

• Applicators and operators shall use appropriate personal protection equipment when using this product

• This guideline is given based on the current knowledge of the product

• Any suggested deviation to suit the site conditions should be forwarded to us for advice and approval before commencing the work

• Please observe the precautionary notices displayed on the container

• Use under well ventilated conditions

• Do not inhale spray mist

• Avoid skin and eye contact

• Spillage on the skin should immediately be removed with suitable cleanser, soap and water

• Eyes should be well flushed with water and medical attention sought immediately

Please refer to the Technical Data Sheet and Safety Data Sheet for full details regarding safe use of this product or contact us for advice.

 

Contact Us

For further advice regarding the use of this product, technical support or a quotation please contact us.